ACT AMC230 Series Gigabit Ethernet Media Converter is an economical series of high-performance converters that comply with IEEE 802.3 standards. AMC230 converters can supervise and configure in real time the situation of remotely manageable fiber media converters.
• Built-in IP-based Web interface
• Supports remote and local management
• Supports IEEEE 802.3X frame flow control for full-duplex mode
• Store and forward mechanism
• Manual IP address setting/DHCP client for IP address assignment
• SNMP v1 / v2c monitor / private enterprise MIB
• Event trap and SNMP trap support
• Speed duplex mode configuration / flow control setting / bandwidth control on TP / fiber port
• Supports port status / Ethernet statistics on both TP and fiber interface
• Supports maximum frame size of 16 kB
• Loop detection / broadcast / multicast / unicast storm control
• Management VLAN / 16 IEEE 802.1Q VLAN groups / Q-in-Q VLAN
• 802.1p Tag Priority / IP address priority / IP DSCP option in
• Quality of Service mode and strict priority / Weighted Round Robin (WRR) QoS policies
• TS-1000 OAM / IEEE 802.3ah OAM / loop back test
• 16 TCP / UDP filter groups
• Password setting, IP setting and devices description setting through discovery utility
• Firmware upgrade via remote Web interface
• LED indicators for easy network diagnosing
• Reset Button at the front panel for the factory default reset
• Choice of fiber-connector from SC, LC, WDM, multi-mode / single-mode fiber /1000Base-SX / LX mini GBIC module
Item | Description |
Standards and Protocols | IEEE802.3x full duplex on 10BaseT, 100BaseTX, 1000BaseT IEEE802.3-2002 |
IEEE802.3u 100BaseTX IEEE802.3ab 1000BaseT IEEE802.3z 1000BaseX IEEE802.3ah-2004 | |
IEEE 802.1d Spanning Tree | |
IEEE 802.1w | |
IEEE 802.1p QoS | |
IEEE 802.1q VALN TAG IEEE802.3X flow control | |
Connector | ST, SC, FC, LC |
Operating Wavelength | Multi-mode: 850 nm, 1310 nm Single-mode: 1310 nm, 1550 nm |
Optical Fibers | Multi-mode: 50/125, 62.5/125, 100/140 µm Single-mode: 8.3/125, 8.7/125, 9/125, 10/125 µm |
Management Port | 1 console (RJ45) |
Serial Port Configuration | 9600 bps/8 bit/none parity/1 stop bit/none low control |
User Port | 10/100BaseTX 10/100/1000BaseTX (RJ45), full/half duplex |
100Base-FX 1000Base-FX (SFP module) | |
Fiber Link Option | Dual fiber/single fiber (WDM) |
Max Frame Size | 1518 Bytes (100M); 9728 Bytes (1000M) |
Transmission Distance | Dual fiber: up to 100 km |
Single fiber: up to 80 km | |
Bandwidth Management | Supports bandwidth control using 64 kbps steps (N*64K) |
LLCF | Supports Link Loss Carry Forward (LLCF) |
Q-in-Q | Q-in-Q functionality |
IEEE802.3ah OAM | AMC230 Series has two working modes: Master and Slave. The central office device runs in Master mode, and customer premise devices run in Slave mode. OAM functions originated from the Master device. |
Link Monitoring | Reports local events to a remote device including Critical Event (voltage and temperature abnormalities) and Dying Gasp (power down). |
OAM Discovery | Searches for remote devices with IEEE802.3ah OAM functionality enabled, and negotiates with remote devices. |
Working Temperature | 0 °C to 60 °C |
Working Humidity | 5 % to 90 % RH (non-condensing) |
Storage Temperature | -10 °C to 70 °C |
Storage Humidity | 5 % to 90 % RH (non-condensing) |
Dimension | Local : 94mm (L) x 71mm (W) x 26mm (H), Remote:150mm (L) x 110mm (W) x 28mm (H) |
Power Supply | Local: 85 V AC to 265 V AC, -40 V DC to -57 V DC Remote: 110-265V AC input, 5V1A DC output |
Power Consumption | Remote: ≤5W |
